Red Barons Wings
 

This appears to have found its way into my garage!

https://farm5.staticflickr.com/4700/...2a76cf9d_c.jpg

Shane

Looks like the top of my drive to me.....
Looking good Shane just how a scooby should ;-)

That looks rather clean. Low mileage as well I bet?

Very nice Shane,

I do hope it was worth the :wife::wife::wife::wife::wife:

Have and enjoy. :five:

Looks lovely - great colour too!!

:SMBLU:

very nice and clean mate :10:

Make a change from the usual silver, blue and green, I wasn't sure but it's growing on me along with the grey leather interior.
Looks clean but rear arches and the rear edge of the sunroof need sorting and wheels need a serious refurb (not helped by me grinding the curb after the test drive).
Only 61K though with a full history and receipts for over £2k in the last 10 months for Cam belt, pulleys, tensioners, MAF and Lambda from Power Engineering and a new air con condensor and re-gas.

Shane

(I can see a change of user name coming up, Red Baron perhaps!)

Nice, that looks very tidy.

Genuine Speedline ST2's? love that wheel on classics :nod:

A wave of the magic wand and it's done ... ;)

Looks a very clean classic :)

looks great shane, nice one:ok:

That does look clean,welcome to the gang!

Makes a nice change to see a red classic..nice one!!!

Looks very nice! :-)

Nice car and gold wheels :doubleup:

Nice one Shane. I will keep an eye out for it.:-)

Me too , not seen a red one for a while now.

Not done an awful lot to her in the last year other than drive her and a service. Had a fresh MOT this morning with no problems and then treated her to a new set of number plates. Following the crowd with a standard size rear plate and a 3/4 size front.

https://farm5.staticflickr.com/4664/...1cd513b8_c.jpg

https://farm5.staticflickr.com/4666/...5b4fdec1_c.jpg

Decat down pipe is next on the list I think and then start saving the pennies for an STI spoiler and get the arches sorted.

Looking good Shane.

I must order some plates up too. Looks so much better with the 3/4 front.

Think I'll start copyrighting that design. Your not the 1st one to use exact same colour and design as mine.

I hadn't realised it was exactly the same until I saw the picture of yours last night. I tried it with a red border and a red to silver and it didn't look right, didnt like any of the other logos either.

Biggest form of flattery mate! I think mine will be the same. Maybe it'll become an SES thing!!

very nice looking. is it a ppp model, really like the wheels.

No, it has a Prodrive Backbox but following yesterdays MOT we discovered it's actually a modified Newage one. Not sure when the wheels found their way onto it. If anyone has a V6 Prodrive ECU kicking around I could be interested.

Wheels look even better when they manage to keep hold of their Centre Caps!!!

Shane

Well, more expense, just like any other Scoob, spotted this at the weekend:

https://farm5.staticflickr.com/4701/...8a3b0055_c.jpg

So a set of Godspeed grooved disks and kevlar pads going on at the weekend and then bed them in on the way to Brooklands on the Sunday.

Going through the paperwork it's had a set of cheap disks and pads in the past from ebay but those pads aren't cheap ones, guess the guy before me put some decent ones in for the track days he did and the disks couldn't cope with the heat they generated. Lucky I spotted it really.

Shane

**** ! yep more money to spend least you spotted it mate

Is it my eyes or are those pads in the wrong way round?

Did you go to Alyn at AS Performance? if not you should have done for the new discs...:nod:

No i think you could be right there mate, they do appear to be in the wrong way round.

Very well spotted Shane.

Did speek to Alyn but was on a budget and got a deal from Godspeed for disks and pads. Pads were in it when I got it, no idea if they're round the wrong way or not but will double check everything when I change them at the weekend

Good spot that man :ok: Perhaps we should call you Hawkeye? :wink:

look to be the right way round (otherwise you would see 2 locator pin holes in the pads there?)
Disc looks properly finished!

Which pads did you go with from Graham?

Just his standard kevlar pads Dave, probably similar to the ones I was going to have off you.

Out with the new,in with the old
 

Picked up a new interior yesterday, leather was nice but a bit slippery and hot when the sun comes out. I must be the only person that fits an older cloth interior in place of a later leather one.

https://farm5.staticflickr.com/4710/...f3e6700f_c.jpg

https://farm5.staticflickr.com/4614/...bd02f548_c.jpg

https://farm5.staticflickr.com/4650/...7e9dbc1f_c.jpg


Should have shed a few kilos as well getting rid of the folding rear seats.

Old style is just foam and wire

https://farm5.staticflickr.com/4669/...931cba01_c.jpg

Loads of metal on the later ones

https://farm5.staticflickr.com/4751/...5da6727b_c.jpg

they look in good knick, and the colours go well with the red bodywork

A couple of small marks but very little wear, will come up really well with a good clean. And they sit a bit lower so I've gained an inch or so in head room.

Always nice to have a bit more headroom, part of me is tempted to retro fit classic interior in my newage, I still maintain the classic seats are the most comfortable!

Bloody sun roof restricts my headroom even more so I need every bit I can get. Almost empted to whack a Carbon Fibre roof on it and bin the sunroof rather than get the rust repaired.

Tell me about it my head is planted on the inside of the roof of mine,classic seats sit so much lower in a newage wish i had kept my last ones i bought to try and put one in this one as pissing me off again every time i hit a hole/speed bump etc.

ps seats look good and in great nick as well

Well, managed a hour or so tinkering time before the thunder storm and finished my DIY PPP conversion.

The car already had the Prodrive back box when I bought it plus the optional Speedline ST2 wheels. First change was the De Cat down pipe, I know the PPP involved binning the centre cat rather than the one in the down pipe but I'm not trying to meet emission regulations, parts to fit it were half the price of the downpipe.

https://farm5.staticflickr.com/4652/...0b79d677_c.jpg

A few months ago I picked up a V5/6 PPP ECU and have been running that for the last few months with no problems, this should peak at 1.1 bar rather than the standard ECUs 1 bar.

And finally I picked up the proper Intercooler pipework this week.

Comparing the original plastic pipework and the replacement Alloy/silicon combination it should improve airflow through the intercooler considerably.
https://farm5.staticflickr.com/4670/...203898bc_c.jpg

It's also nice seeing prodrive written on bits under the bonnet :)

https://farm5.staticflickr.com/4756/...b8e5a256_c.jpg

Next stop is SRR next month to see whether I've wasted my money on the ECU or not as I have my doubts over it's authenticity.