05 black blobeye ppp
 

I don't feel like this is a project, just little mods to make it my own - so i thought i'd stick this thread in here :)

Got the car March this year.

2005 black blobeye with the Prodrive performance pack.

Day I got it

http://i.imgur.com/nr7fgey.jpg

After a good clean

http://i.imgur.com/eaoVGqR.jpg

http://i.imgur.com/5l2ePGC.jpg

Mud & dust

http://i.imgur.com/72XIxWC.jpg

Blackened headlights, no splitter at this point - I had to remove it for the mud

http://i.imgur.com/d6nvv3G.jpg

Recently fitted a gauge pod, only got a clock in it at the moment, boost gauge in the post.

This may not be the best way, but it worked for me...

This is where I took the power from for the gauges, it's the plug for the clock -

Top to bottom:

12v
Earth
Lights on
Ignition on

http://i.imgur.com/RIaNtO1.jpg

Soldered additional wire on the end of the Prosport plug, firstly to add strength and secondly to make sure the scotch locks got a good contact. Shrink wrap to keep tidy and protect -

http://i.imgur.com/aHDAA0o.jpg

http://i.imgur.com/ZITZDDj.jpg

In theory, you should be able to connect one of the cables to the lights cable on the clock plug, but it wouldn't work for me. So I used the cig lighter instead. Green wire is the one I needed.

http://i.imgur.com/rpKW4Ga.jpg

After I had connected the rest of the wires to the plug using scotch locks, I covered in corresponding tape so it's easier to identify which is which in the future.

You can also see in the background where I extended the cables for the alarm LED - my LED is broken though, so I need a new one.

http://i.imgur.com/IPoi1IK.jpg

This is it so far, just a clock haha :)

Ignition on, lights off

http://i.imgur.com/x2Q6UZy.jpg

Ignition on, lights on

http://i.imgur.com/G8j2TtZ.jpg

Next gauge is a boost gauge, not sure what to use as the third yet so I ordered a 52mm blank.


Plans -

Tint the windows
Different wheels, in black
STI dial cluster
Refit a splitter
Impreza car mats
New mud guards
STI bonnet scoop & intercooler
Fit Hella horns


Thanks!
Foz

Nice work :)

Either oil temp or oil pressure for the other one.

Looking good & always helpful to have a detailed record of your work :)

... just don't cut the red one :-D

Thanks guys :)

Yeah I'm thinking an oil temp gauge would be best, already have the stock oil pressure - regardless it's very bad times if the pressure drops.

Replacement splitter arrived and fitted today -

http://i.imgur.com/0Zrh1dt.jpg

Looks very nice

Where's the mud and dirt photo taken, looks military?

Yeah, the War and Peace show at Folkestone racecourse.

I go every year :) Was good fun driving around in the mud haha

Made some more progress with gauges this evening, took much longer than I thought it would.

However, now I have a Prosport clock and a Motor Meter boost gauge - exactly the same style just a different logo. Somewhat annoying, as the gauges don't match now (just the logo) so I'll have to fix that next pay day.

I located the boost sensor behind the glove box. There was a spare bolt at the top and I had some nuts laying around.

Boost pipe goes through the grommet to the rear of the glove box.

Not pictured, but tied all the pipe and cables back to keep them out the way. Also a cable comes out of the top of this into the back of the gauge.


http://i.imgur.com/73Hvyyb.jpg

http://i.imgur.com/EielXZa.jpg

Here is where I put the t-piece. Only concern is that it's plastic, and it gets quite hot so it could melt. I might have to look at getting a metal one to replace it.

Couldn't really hide it away, as the pipe to the DV was tight as it was.

http://i.imgur.com/2gOFnZg.jpg

As mentioned in the previous post, I broke my old LED.

Bought a new one off eBay, drilled a hole in my pod and glued it in. I decided not to use a bezel around the LED as I think it looks much neater and less obvious (When LED is off).

Rear

http://i.imgur.com/o4yFmXT.jpg

Front

http://i.imgur.com/Yp85wDl.jpg

As with all the cables, I made them so that I can remove the lot if I need to. These are for the LED. Later wrapped in insulation tape.

http://i.imgur.com/BCZiw9U.jpg

Random picture of rear of the pod

http://i.imgur.com/8Js8DfU.jpg

Got a 52mm blank to match the dials until I get a third. Can barely see the LED :) You can see the different logos here...

http://i.imgur.com/mdqWGHB.jpg

Night shots

http://i.imgur.com/Xiaqq9K.jpg

http://i.imgur.com/0EyYf4t.jpg

Also out of curiosity, what boost should I be getting on a PPP WRX?

According to the gauge i'm hitting 20PSI - is that normal/right?

Thanks,
Foz

Looking good, one more to go :ok:

theres a set of red defi sti clocks on scoobynet atm - think theyre £400 though which is a lot of dosh - one of mattyb posts iirc

Looks awesome in black. Another PPP 05, will keep my eyes open for you in and around the Medway Delta :10:

Fitted the Hella Supertones this evening.

Didn't take many pictures of the progress.

Had to make a few wires up.

• One from relay to live (with inline fuse).
• One from relay to earth.
• One from the relay to the Hellas, 2 connectors at one end (for each horn)
• One from the Hellas to earth, again 2 connectors at one end.
• Final wire was the one from the original horns connected up to the relay.

Live with fuse -

http://i.imgur.com/L1fpIne.jpg

Earth for relay and horns -

http://i.imgur.com/HtInRoC.jpg

Relay with just live (left) and earth (right) connected. I located this in a free hole above the near side headlight -

http://i.imgur.com/Mr9hyLQ.jpg

Relay all connected, not very clear but the top is the original horn connector, and bottom is to the horns -

http://i.imgur.com/bKE8j8F.jpg

http://i.imgur.com/jd5xOJe.jpg

Bolted in and connected up. Used some extra washers to space them back a bit so that they didn't hit the grill. Wires tidied up since pictures too! -

http://i.imgur.com/7pedCJA.jpg

http://i.imgur.com/4dUY5Tl.jpg

Final product - They're incredibly loud!

http://i.imgur.com/zJt7J2v.jpg

However I did knock over my box of connectors :doubledown:
http://i.imgur.com/gu5a3rJ.jpg

Thanks!
Foz

those hellas just look so cool especially on a black scoob - id fit them just for aesthetics ! nice :-)

Main reason I got them :ok:

yup - I bet people not in the know about all things Scooby think theyre twin nitrous turbo boosters or something ! lol they do look a bit more then horns

Rear brakes needed replacing, so I bought discs and pads for front and rear from godspeed - quick delivery and well packed. No complaints there!

Only replaced the rear brakes for now, waiting on a fitting kit for the fronts.

Old Vs New

http://i.imgur.com/3cGzEGE.jpg

Rear fitted

http://i.imgur.com/GmPuR0r.jpg

Fitted an STI scoop

http://i.imgur.com/CESYl8O.jpg

Also I wanted to be able to control when my gauges change colour.

I got a 3 way switch. Off for white, one way for red, and the other way for "auto" - which works off the lights - Lights off = white, lights on = red.

Need to find some way to secure the switch nicely, might cut down a piece of plastic to fit in place of the ash tray.

http://i.imgur.com/Qmz19pm.jpg

Thanks
Foz

Cool, some nice mods there.:doubleup:

Couple bits done this weekend.

Fitted the front discs/pads.

http://i.imgur.com/o9hXGj2.jpg

Need to repaint my calipers sometime soon.

http://i.imgur.com/qUUtsLU.jpg

Also found that I need a new drop link.

http://i.imgur.com/N5p9Heg.jpg

Made up a little plastic plate for my switch, and for any future switches.

http://i.imgur.com/F4A9jgs.jpg

Also washed and polished but didn't take pics, not sure why.

good progress made :five:

A nice bit of work there :doubleup:

Couple bits done recently.

Wired in USB power for my phone, fitted a permanent mount etc. (no pics)

Bought a snow foam lance - Great fun!

http://i.imgur.com/F8XeMWZ.jpg

I've removed the orange plastic from my headlights and replaced the indicator bulbs with chrome ones - I think the front end looks loads better.

http://i.imgur.com/ki8743u.jpg

Really want a new set of wheels.

much better without the orange bits in the lights :)

Good progress! :)

Very nice. Car is looking really good. :doubleup:

Awesome :-)

Looking good, detango definately helps :ok:

Looks stunning. Which lance did you go for?

I bought the Karcher one off eBay.

Great project there mate, keep the updates coming.. Love the car bud

Lance looks like a bargain ;)

Bought some new floor mats, no pictures though - much nicer than the generic ones it had before.

Had the windows tinted today -

http://i.imgur.com/bwuvzcg.jpg

http://i.imgur.com/FxzZsPJ.jpg

http://i.imgur.com/YZYqmTw.jpg

http://i.imgur.com/DoGN3DT.jpg

Finally bought 2 more gauges for my pod, Oil temp and Oil pressure.

So now I have Oil temp, Oil pressure and Boost.

http://i.imgur.com/E1wBsw5.jpg

Also got some new wheels! Was looking for Rotas but these came up and they were a bargain. 18x8 - looks loads better. Needs to be a bit lower now though.

http://i.imgur.com/pVkLrTS.jpg

http://i.imgur.com/0NLN0ED.jpg

Looking good :nod:

Some nice mods there, looks really nice.

Wow, nice job on the gauges. I'm scared of wiring!

Very nice.