White STI 5 2.35ltr build

[seventune]

Some of you will have seen this on the other Scooby forum but a quick "fill in" as i'm new to the forum.

I bought the car as a 2.1ltr stroker built by OMA in Ireland that, as I understand, was part ex'd in at Hurst Cars. The brief spec was
2.1 stroker, forged rods and pistons with EJ257 nitrated crank, APR studs
MD321 turbo and generic front mount
Blitz Nur Spec R muffler and mid pipe, HKS front pipe.
uprated intank pump, 740cc side feeds and Sytec fuel pressure reg
Alcatek ECU and Greddy Profec B boost control
BC coilovers, Rota 18" wheels and Late model STI 4 pot Brembo conversion
6 speed conversion from Jap spec C and diff to suite.

Not a bad spec and I would have been happy with it as it was had it not gone a little wrong. But here is the car as purchased.









The Nur spec had been completely gutted inside so the noise was.... well shall we say extreme as I was in essence unsilenced. Mad for a fun drive home in any case. Even for me however it was too loud. So I pulled the Nur Spec off and made up a new temporary fit.







Also changed the Blitz filter for a BMC which require a new bit of pipe

[C. J.]

Looks good and a 2.35 will serve you well

[seventune]

I then got some inlet manifold spacers from CDF as I had plans to rotate the inlet manifold. and mess around with the turbo location to get the intercooler pipe work shorter. Do that went a little like this:



Spacers



A few bits of the wiring had to be lengthened for the idle control valve and TPS. I also removed the power steering at this point because the pump was faulty.



Ended up like so:



As I mentioned a touch of turbo messing was in order. I converted the MD321 over to an external gate as I was getting boost creep in virtually every gear and also rotated the turbo around to loose the U bend in the I/C pipe work on that side. I also remade the top part of the down pipe to an 'open neck' version.





The final result was :

[seventune]

Originally Posted by C. J.

Looks good and a 2.35 will serve you well

Hope so

[seventune]

Unfortunately some months later the car developed a knock form the bottom end and then eventually let go on the way home from work one night. The following weekend I set about the strip down.







Then took the motor up to the shop and got stuck in



Shouldn't be water in that bit! And there should be a piston in this bit!!!









Needless to say that the motor was trollied!

[seventune]

Given what I had spend on the car it had left me with not many choices I the way I could then move forward to rebuild the car. I have used a lot of parts I already had (some a bit over the top) but bought some more choice parts along the way.

And it started with this. A sterling find on ebay.



Gaskets and bearing where bought from RCM. ACL bearings, 14mm studs and thicker head gaskets.



Pistons I got though Wiseco, we use them for other things.



Now the block though and EJ22 was an open deck EJ motor. This could lead to the same liner issue that I had had before so I decided to 'pin' the barrels. This was done with ally dowels that where put into tight channels that where spark eroded in.

[seventune]

Crnak and rods went off to be inspected by a specialist as I didn't have the funds to buy new in the grand scheme of the build. They where dressed,cleaned and tolerance and where given the all clear for use.



Oil pump was also trolled after the motor let go so that was replaced with a 12mm modified RCM item.



Fueling was also addressed with a set of 750cc RC injectors that I had, which will in due course be aided by a set of secondary injectors of the same size, a pair of Bosch 044 pumps, Holley hi flow FPR and then I decided to build a swirl pot for the boot so stop the whole system getting starved. The issue with the injectors was two fold. The current items where side feed and Hi impedance and the RC are top feed and low impedance. So I made some new rails using the Aeromotive billet rail and sourced a second hand AEM injector driver from CPL.





Swirl pot



AEM installed

[seventune]

Now whilst I was waiting for bits and pieces to turn up I had a few other bits to get on with. I had decided to get a new power steering pump and relocate the reservoir and water header tank. I made both into one, sort of, and have mounted them off to one side where the ABS used to be





And the bracket for the brake and clutch reservoirs



Now the fun bit. The turbo that I had 'lying around' was a Garrett GT4094 with .95 turbine housing. I bit big but with MD321 being out of action I couldn't go and spend another £1,000 on a new turbo charger so u used the GT40. Hence the bigger fuelling system. Should have pointed that out earlier. Anyway more pics.

Now I also had a pair of F38 Tail wastegates from my RX7 which would be ideal for the GT40 twin scroll as you can see pictures. Turned out with the turbo location I wanted and that the pair where a very very tight fit so eventually I bit the bullet and bought a single MV-R gate to do the job.

MD321 and GT4094



Equal length header in the making!



Tacked up at home on the bench on the destroyed engine



Buzzed up primaries



twin scroll up pipe



Almost finished article!





At this point I was still trying to get the twin gates in but but later, as I said, I went with the single MV-R which I plumbed back into the down pipe.

[seventune]

Needed an air box for the filter to sit under the hood scoop. I'm not totally happy with it so it may well get changed in the future. I also remade the crank case breather tank which mounts off the airbox.



Using an ITG filter that's actually for a Honda Accord!



mock up



Moving onto the swirl pot in the boot:

First off the boot floor was modded:





Then the first 044 placed in the tank and then a pair of -8 weld ons fitted for the feed and return lines.





This does still need finishing off but here are the hard lines in the boot thus far:



and intercooler pipe work for the temporary cooler. I've modded the current cooler as i'm waiting for a new core to turn up but the new pipe work comes in under the lights

[seventune]

Then set about the exhaust. All new 3" system fully Vbanded. Aim here was as straight and possible. The mid pipe:



Rear muffler







ENGINE STUFF!!!!

Heads skimmed and rebuild



EJ257 crank and rods clearenced :



Then checked the deck height etc with the pistons before final assembly and cracked on getting the heart of the build built!





Cosworth cam belt



ready to go in..... almost

[seventune]

I had decided that with the engine being now being a 2.35ltr motor after the re bore with the 97.5mm Wiseco pistons etc it could still do with a helping hand getting that GT4094 moving. The car when purchased had an uprated organic clutch which wouldn't be up to the new power range of the car. I opted for a 7.5" Quarter master twin plate. I had used these in the past a very much likely the results. New smaller clutch meant new flywheel.











This lead to another small issue. The stock 6 speed box and clutch is designed for pull type clutch. This is a push type. So RCM sorted me an AP racing bearing and I made the adaptor to suite the box and clutch height along with the new lines.







Now the built motor could finally be installed

Checky pic of the header before fitting up for the last time





and in:



That's pretty much how she sits at the moment. Just a case of refitting everything. Making new lines here and there and just getting on with it!!!!

[Sti mayhew]

Wow that's fantastic, there's some very clever stuff done there and all nice and tidy to. Well done can't wait to see it finished

[Steve_PPP]

Nice project, loving the work on the headers!

[NL03Scooby]

Cracking write up, some real awesome stuff going on there and really interesting to an engine amateur like me, I enjoyed the pics...

[Hongkongfooi]

Great build this.you clearly know what you are doing. Have you your own business in engine builds etc ?

[SpecB]

Incredible workmanship and attention to detail, those headers look incredible.

[Bolesroor]

Great write-up, loving the pipework

Nice plate on the Maserati BTW "is it yours"?

[555_Si]

Wow, impressive indeed, very nice work. I guess power delivery on that turbo is going to be entertaining.

[Firelight76]

Thats super cool! I wish i had an inkling about how to do any of that!

[Ginola]

That is awesome stuff, the turbo setup and manifold + clutch setup is very different! really looking forward to the next instalment

[seventune]

Thanks for all the comments people. Much appreciated

Originally Posted by Hongkongfooi

Great build this.you clearly know what you are doing. Have you your own business in engine builds etc ?

Not as such. Whilst I do build my own motors I work for a tuning company in Berkshire that builds custom turbo and drag bikes. I do the fabrication there in house. I did run my own company for 6 years doing custom fabrication prior to that but that came to an end. Long story short I sub let the workshop from a guy that rented the site and the Landlord sold the land from under us to a developer. Still doing what I love though so sort of maybe worked out in the end.

Originally Posted by Bolesroor

Great write-up, loving the pipework

Nice plate on the Maserati BTW "is it yours"?

Ha ha, no. The Maserati is my step dads car. My Impreza is over at my Mum's as I don't have the space for the car where we live on the road. Well not in its current state anyway!

Originally Posted by Wagon_Si

Wow, impressive indeed, very nice work. I guess power delivery on that turbo is going to be entertaining.

I have seen a couple of dyno graphs on 2.1 stroker engines and one from a 2.5 all with GT4088's (Mines a 4094) and I think you would be surprised. They spool up the same as a GT35. As the turbo is not the ideal choice I have come to a compromise on a few parts of the build to aid spool.

[seventune]

New toys. I haven't yet decided what is discs to get in there. Need to check the measurements on the wheels to see what I can get away with!

[Ginola]

Oo now that's different too!

[seventune]

Yeah will be a bit of messing around with caliper carriers to get them in there but they offer a much larger swept radius over the STI four pots. Will allow me to run a 355mm disc.

She's starting to look like a car again under the bonnet! Still lots to do but taking shape.

[SpecB]

Looks a great job there, very clean install

[seventune]

Cheers chap. Truth be told I'd have liked to have painted the bay aswell but a good clean will have to do for now!

[seventune]

Bit more plumbing done. I decided to put a tie rod in for the turbo for an extra added support. Unsupported weight of a turbo on a red hot set of headers is one of the biggest contributors to cracks in manifolds in general, always worth bearing in mind. I'd whole heartily forgotten how long it takes to put hard lines in! Breather pipes done along with the water pipes and power steering. With the power steering I have used a combination of hard line and swaged fittings to get down to the rack.

Tie rod support



Engine bay with the hard lines in



Slightly better view of the water header and power steering tanks



Slowly slowly catchy monkey!

[Ginola]

Won't the engine movement on acceleration cause problems with the hardlines?

Looks great btw

[seventune]

The header tank is yet to be rubber mounted. Waiting on the bits from suzuki which will solve that issue. The breather bits will all move with the engine and the power steering lines are half rubber hose on the rack end. If everything was hard mounted to the body and then to the motor then yes your right you can get issues with the fittings when using hard lines.

[Ginola]

Aaa cool! Looking forward to seeing more most interesting build thread I have seen in a while

[seventune]

Thanks dude,

Couple of loose endy bits tied up. Bit more wiring and behind the scenes stuff done like running lines etc. OPB pedal box is now in. I managed to get a second hand one off a mate that's a classic specific box.

After other bits taking so long I now have the intercooler core for the V mount intercooler set up. That's nearly finished. Rad end tanks are done. Just need to weld on the pipe for the hoses. Waiting on the ally for that. Will start making/welding the brackets and mounting point on the car and coolers so I can get all that in situ permanently then move onto the pipe work. Makes having done the front mount mods a little pointless but there we go!

Also changed the mount for the turbo from the bulk head to the engine. Machined a little tower for it to mount too. And you can see in one of the pics that the FPR is there now too.

Turbo mount:



Engine bay shot as it was before the new core turned up! FPR in there on the air box, which i'm still not totally happy with. The air box I mean.



Just a snap while the car was in the air of the whole exhaust. Shows how the header squirrels around. I tried to keep the system as straight as possible.



Quick "throw in" pic of the v mounted intercooler core. It won't wind up sitting quite there but gives a good enough idea.





With the end tanks welded on and nearly finished up:





Will get a bit more done in the morning and hopefully get it all mounted in there with the pipe work by the weekend!

[scotty]

Loving this thread some cracking work and welding keep up the good work .

[seventune]

cheers dude,

righty,
Intercooler finished and coloured:

As you have probably see in the older pics I've had to mess aground who the slam panel. This left head headlights and remaining section of the slam panel a touch wobbley so I had knocked up a bracket to take up the slack. Not the prettiest but will do the trick.


Then the intercooler in place. The rad is in place but not finished yet. Will get the intercooler pipes sorted in the morning.

[Hongkongfooi]

awesome stuff.....must be near paint the bay and get it running?

[Ginola]

I'm really really liking the V-mounted rad/intercooler, its the way the WRC cars do it so something must be right about it!

[seventune]

Thanks. Yeah inspired by the old wrc set up. Always wanted to do it!

So got into the build today got a fair whack of niggelly jobs done. Everything is wired up and in aside from the rad fans (need to buy those still ) and one of the fuel pumps in the rear.

All of the vaccum plumbing is done. Along with most of the pedal box lines. Still need to do the brake lines. I desperately need too redo the HT leads. I can't live with those being red. An upgrade to new age coil packs will be in order at some point. Winds me up the BOV and wastegate being red. Few more of the pipes still need coating too along with the rad. I was hoping to get all the water system tied up today but the tube never turned up as promised by the supplier.

Oil filter relocation and cooler is also now in. Need to make some ducting for that and also for the v mounted intercooler.

Vac pipe stuff behind the plenum



v mount intercooler brackets either side now in



oil cooler and relocated filter





Can anyone tell me why my thread is just one long page instead of several with fewer posts?

[scotty]

That v mount cooler is looking pretty damn sweet now but how are you going to shut the bonnet or have you got a mad crazy mod idea up your sleeve for the bonnet .

[Steve_PPP]

Originally Posted by seventune

Can anyone tell me why my thread is just one long page instead of several with fewer posts?

If you go to User CP on the blue bar at the top ^^ then Edit Options, there's a setting in there for 'Number of Posts to Show Per Page'. If its set to forum defaults, then thats 50 posts per page before it rolls over to page 2.

This just seems really long on one page as its filled out with build photos

[seventune]

The bonnet will be on aero catches. Just not got them on yet!

Finally got all the v mounted intercooler in and finished. You'll note that the rad pipes are cut and welded. They won't be staying like that for too long. Had to do it that way so I could figure out all the best and routing as it quite tight under the cooler. I've also put in a 2nd filling point for the coolant to help with bleeding the system. But it's all in and for the most part I'm pretty happy with they way it all sits in there.



You can see how I needed to snake the pipe under the cooler pipe. Now I have the angles etc I will be ordering proper bends to make it nicer.





With the bumper back on....



All stelthy like...... no one will ever know

[scotty]

Like that looks so subtle .

[Bytes]

music and 'feed me, feed me now!" spring to mind

Great to see the updated look now with the bumper in place. Are you planning on adding a grille such as the zunsport? Liking the pipework mods too

[seventune]

Few more bits done since the last update.

Tyres needed replacing. This was a hard one actually. In the end I settled for the NS-2R's. 225/40/18. Given the reviews in both the dry and the wet, on and off the road for the money they worth a shot. People have said how they are better than the R888 in terms of longevity, grip and wet grip (most importantly on UK roads). That have been compared to the AD08 Yoko on a number of occasions and not come up too bad.





I also think the fatter wall gives the car a more purposeful stance too.



Next up was the pedal box. This is now in fully but I only have this pic. I do still need to make the heel plate to go over the cylinders.



Where the mods have been made for the V mount intercooler I have welded in a larger brace bar at the bottom. This also gives more room for the fans on the rad.



With the bumper back on



Few interior bits on the go. I wanted to change the wheel and boss for OMP items. I love a nice quick release but given they are race parts they take a bit of getting in the car without have the steering wheel hitting you in the chest. With the pedals where they are the new further back seating position required a dish wheel. I opted for a bolted quick release over the welded type I have used before as they work better with the steering coloum controls. I'm in the process if making the boss to fit the spline on the coloum but a small spacer was also need to get the horn button in the wheel as the wheel sits flush on the racing boss.



the spacer



Will finish the other bit on the morning and the wheel mounted up.

I also wanted to put kill switches on the pumps, fans and ignition. I couldn't resist a push start either. I've ditched the double din stereo and utilized the lower space for the switch panel






So close to starting her up now. Next couple of days hopefully.

[Steve_PPP]

Liking this a lot, look forward to seeing your future posts

Originally Posted by seventune

Tyres needed replacing. This was a hard one actually. In the end I settled for the NS-2R's. 225/40/18. Given the reviews in both the dry and the wet, on and off the road for the money they worth a shot. People have said how they are better than the R888 in terms of longevity, grip and wet grip (most importantly on UK roads). That have been compared to the AD08 Yoko on a number of occasions and not come up too bad.

Interested to get your opinions on them as I'm probably getting a set before heading to the Ring in May. Did you go for the 120 or 180 compound?

[Ginola]

Just been through this again really like the work, cant wait for the next installment, love the V-mount rad/intercooler (works for WRC!)

[seventune]

Cheers guys.

Got the steering in this morning. I'm going get a little boot to sit up being the new boss to cover the gap between the coloum and plastic covers. Now you may think way go to all the effort and not just buy and off the shelf adaptor. The answer is the distance. With the pedals being further back I bought a dished steering wheel to compensate. Then with the quick release mechanism it added a lot of length to the wheel assembly. I made this boss to make that all as short as possible. In doing saves about 2" which was perfect.

I cut the spline out of the stock wheel. The made an ally ring so that the two would be an interference fit. Then welded them front and back. This boss would then take the wheel hub.

Centre machined down



new ring

[scotty]

Love a bit of custom work as you can get a better finish looking forward to the next phase of updates .

[seventune]

Originally Posted by Steve_PPP

Liking this a lot, look forward to seeing your future posts

Interested to get your opinions on them as I'm probably getting a set before heading to the Ring in May. Did you go for the 120 or 180 compound?

Originally Posted by Ginola

Just been through this again really like the work, cant wait for the next installment, love the V-mount rad/intercooler (works for WRC!)

Thanks guys, next update should be start up

The tyres are the 180. Bit more ware in them hopefully. I'll let you know how I get on with them.

Originally Posted by Bytes

Great to see the updated look now with the bumper in place. Are you planning on adding a grille such as the zunsport? Liking the pipework mods too

cheers fella. To answer that question. No. No grill. I'm really not a fan of big mesh grills in the classics. looks a bit more purposeful without.

Originally Posted by scotty

Love a bit of custom work as you can get a better finish looking forward to the next phase of updates .

Thanks dude

[bang.]

woowww great project

i would like to see one video of this superscooby

[bang.]

that feeling you have with the pedals?
compared with oem

[seventune]

Thanks dude. It is a different feel on the pedal compared to OEM but not unpleasant. A big factor in that is getting the cylinder size correct.

[C. J.]

Even working out the correct cylinder size doesn't always work . Had someone work them out for us and went .7 front and back . Had to stamp on the brakes , changed the front to a .625 and awesomeness was found

[seventune]

Well............

Got the old girl running.

BUT its never as simple as that is it. After ordering the new seal and a couple of other bits off of RCM I got around to getting the beast running. As I wasn't 100% where to start looking given the injectors had a pulse signal. SO I pulled them out and ran them through the injector cleaner. Remade some of the earthing points on the chassis and engine. Re checked earths on the ECU and AEM unit along with power supplies. Changed the battery for a new larger item. Refitted it all and pressed the button. She tried so hard to fire it was agitating. So. Swapped the plugs from 8's to 6's. And turn the fuel pressure down on the FPR. Pressed the button again and she fired up a treat

Happy days.

Having had the car the fired it was time to replace the oil seal. Personally I find it quicker to pull the motor than drop the gearbox. Undo the bolts unplug the wiring harness and bosch, out. Anyway before that, oil out. Aweful lot of debris. Turns out the crank ate the rear thrust bearing. Long story short when the 2.1 engine let go the crank went off to a specialist to be analysed, checked and all that. It came back with the ok to be reused in the new build. Cranking the motor over and running it proved other wise.

Absolutely everything has been scrutinised at the end of which a new EJ257 crank/big end and main bearings has been ordered from RCM and should be with me in the next couple of days so I can rebuild the old girl again. Hopefully this time to a more positive out come.

On we go.....

[SpecB]

That's a bitch - any comeback on the engineering firm that checked the tolerances for you?

[seventune]

I'll have a chat with them and see what happens but im not going to go nuts at them. You can't do 100% maths test every day of the week.

[seventune]

Woohoo

[scotty]

I hope that wasn't to expensive to buy .

[seventune]

Originally Posted by scotty

I hope that wasn't to expensive to buy .

I wouldnt say it was cheap dude but very much needed .

[scotty]

Originally Posted by seventune

I wouldnt say it was cheap dude but very much needed .

If you can't be £250 for a brand new one then you got robbed

[seventune]

Was considerably more than that dude. It's a genuine niterated ej257 crank.

[Ginola]

Originally Posted by scotty

If you can't be £250 for a brand new one then you got robbed

that's the price of a half decent second hand one

[C. J.]

Originally Posted by Ginola

that's the price of a half decent second hand one

Unless you buy from the states

[seventune]

Originally Posted by Ginola

that's the price of a half decent second hand one

Yeah. There was no way after the damaged caused that I was going to buy a second one. That's a brand new niterated item. Hopefully that will be hidden away back in the cases where it belongs

[scotty]

Originally Posted by Ginola

that's the price of a half decent second hand one

Not for me it's not a friend is selling me his brand new one for that price don't know where he got it from so I check how much they where and I had to buy it .

[seventune]

Don't blame you for that money dude. Nicely done

[scotty]

Originally Posted by seventune

Don't blame you for that money dude. Nicely done

Thanks don't know what I'm going to do with it yet .

[seventune]

Got to be a spare motor hasn't it?

Didn't get in as early as I'd hoped this morning to get on with the engine so I fitted the aero catches instead....

[seventune]

Well bottom end back together. Pressing on to get the engine back in and running by the weekend.

I want my scoob back on the road.

[seventune]

Several years later.....

[seventune]

Well the motor is now 100% built and ready to go back in. I have been even more scrupulous with checking and re checking everything to avoid the crank issue happening again. There was no obvious cause for the crank mashing the rear face of the thrust bearings.

First big thing to change was the piston to head clearance. With the new crank the piston where 20 thou higher than previously. At lowest tilt they where .013" above deck and on full tilt at their highest .031". With the 1.5mm ( .059") head gasket there was no real room to allow for rod stretch. In the turbo bike we allow .040" rod stretch so I took some meet off the top of the pistons to gain the extra clearance.

Crank then the new nitrated crank got clearance, re clearance and clearanced again on both main and big ends.

End float was checked I don't know how many times which I just right ;D

There was one other concern that I had come across before. This invovled the hydraulic clutch bearing. I've seen it before where the spacer behind the bearing has been too thick and when the engine is installed the sits butt up against the clutch cover. Not only not having and air gap as it should but actually being forced up into the clutch cover and also taking up the end float in the crank and mashing thrust bearings. That also being a concern the heights where check over again and on both the engine and gearbox side and was all fine as I had hoped with the required 2.4mm air gap.

With every thing checked it ready to go back in. Plan is for Monday.

[seventune]

There are a couple of issues to report but it's a bit long winded on the phone so i will do that bit later on the lap top but in the mean time.....



Still needs some adjusting is just sitting in there at the moment.

[Rdlangy1]

Just read through this and good read - amazing job you've done there, and be good to see it running again - a lot of time and effort gone into that

[seventune]

Yeah getting over the last hurdle and actually getting the car back on the road has been really hard. Crank issue initially. Then the electrical issue with the stock loom (will explain more when I get a chance).

Want to get a few bits on the body done this week. Then I can finish getting the last few mechanical bits sorted and we're there.

[Ginola]

Really really looking forward to seeing this beast in the flesh glad your finally seeing light at the end of the tunnel

[seventune]

Few more weeks hopefully then mapping for running in

[seventune]

So then. Electrical gremlins are a real pig. But ever cloud has a silver lining. As you know the car is fitted it an AlcaTek ECU. I have been trying to get them to talk to me about making some changes to the ecu for absolutely months. Eventually I decided to not have any changes made to the ecu and just buy a proper one buy in the mean time just get it mapped for the current mods. Anyway reinstalling the loom and engine this time has unearthed an underlying electrical issue. It's started with sensor ground wires carrying 8volt live feeds. Which I traced back into the loom then the ecu. Once that was sorted other singles appeared to be incorrect. The loom that had seen far better days before I had even got into looking for the faults. After finding bare wires, doggy taped up and crimped connections I was time to start fresh. Given the lack of contact and lack of support from AlcaTek I decided that if I was building a new loom it wouldn't be for that ecu. So I bought this instead

Nice Syvecs S6



Few other little bits got done whilst I was waiting for the Syvecs. Bonnet is now finished and ready for paint





Finally got around to painting and fitting the STI 6 spoiler. I was hoping to paint the front bumper today but the weather is looking a bit bad.





Also got all the water system back in the bay and thought I'd treat the turbo to a cozy blanket





All the bits for the loom are ordered. Hopefully all be with me next week and I can look towards actually driving the old girl

[Rdlangy1]

that's one mean looking beast

Awesome work...

[C. J.]

Making the loom is not too bad , just take your time thinking about it 👍

[seventune]

Thanks guys

[seventune]

Started getting the power steering in.

Buried it in behind the front bumper on the drivers side. Its an electric MR2 pump. Will be interested to see how it works. I also found some grot under there so sorted that out too while I was there. need to add to the bracket and some extra support as its a heavy pump.

Grot:



Pump:



Grot fixed and pump in place (but not finished)

[seventune]

So added some extra support to the power steering brace. It's now all ready for wiring. As it's sitting up in behind the front bumper I just mig'd it up a bit brashly. Does the job.






So that ended up down here like this



Now slight chance on the fueling front. I was going to run 8 injectors long term (still might) but in order to get a few more functions out of the Syvecs I have changed the 750cc RC injectors for some bigger Bosch units that I have 'borrowed' from the RX7 build. Just given how long I've had them I bought a refurb pack and gave the a bath



Mid cleaning





So onto the next job....

[seventune]

Couple of trivial bits on the go while I'm sorting out the wiring loom plugs and pins etc...

First thing was to get a set of late model individual coils. Hopefully this should help with the performance and if nothing else makes for a nicer tidy engine bay in loosing the mid mounted coil pack and bright red HT leads!



net result without the coil in there.... much neater



The other thing I have been poking around at is the lights. I have seen a couple of the version 5/6 cars with modded blacked headlights. I think it look very cool so I have set about doing mine. There was another small issue to tackle too. As I have the oil cooler one side of the front bumper and the power steeing pump the other I have removed the indicators and little black plastic infill from the bumper. My decision was to move LED indicators into the side light housing whilst blacking them. I used a set of LED bike indicators.

Started with these:



Then did this:



Threw them in here:



And wayhay:



So with the indicstors and side lights in the one housing I can set about ducting the cooler and pump

Oh and here is a painted pair next to the pair I'll be doing in the morning

[Ginola]

Liking the indicator mod I'm neither for nor against the blacked headlights on a classic, need to see them on the car done to decide which side to fall on :P

[seventune]

I was fairly chuffed with the indicators to be honest. I was thinking for ages about the best way to get an LED strip in somewhere that would work and all that rubbish. Then when up stairs in the shop to get some fittings for a job and what's on the shelf. Set of cheap led bike lenses. All of a sudden it seemed so simple!

I like the black lights but I know it one of those things that splits people. I saw a US 2dr on the North American Scooby club in white with blacked lights and it just looked cracking. Whilst my main headlights are in very good nik the side lights are looking old. I'll keep my eyes out for a good condition pair as of and when.

I'll pop some pics up once the grill and bumper are painted and back on.

[scotty]

Originally Posted by Ginola

Liking the indicator mod I'm neither for nor against the blacked headlights on a classic, need to see them on the car done to decide which side to fall on :P

Well I take it you never notice mine then I forgot you were to busy ogling my wheels lol .

[scotty]

Originally Posted by seventune

I was fairly chuffed with the indicators to be honest. I was thinking for ages about the best way to get an LED strip in somewhere that would work and all that rubbish. Then when up stairs in the shop to get some fittings for a job and what's on the shelf. Set of cheap led bike lenses. All of a sudden it seemed so simple!

I like the black lights but I know it one of those things that splits people. I saw a US 2dr on the North American Scooby club in white with blacked lights and it just looked cracking. Whilst my main headlights are in very good nik the side lights are looking old. I'll keep my eyes out for a good condition pair as of and when.

I'll pop some pics up once the grill and bumper are painted and back on.

Did you say you are looking for a set of black side lights guess what ive got a spare set in really good condition as they are my spare set .

[Ginola]

Originally Posted by scotty

Well I take it you never notice mine then I forgot you were to busy ogling my wheels lol .

I spied them! , still on the fence though need to see more

[seventune]

So waiting for some bits ti turn up and again.... I haven't been about to just leave the old girl alone.

Started playing with the intercooler pipe work. Because of the blue fittings on the fuel lines and headers tank I decided to accent them with titanium pipe work.

All chopped and a test fit once it's all tacked up.





Then a bit of heat before welding to colour it...





Oh.....

And this happened.

[seventune]

Lots of welding and the second ic pipe to do.

[Red Baron]

May be a lot of work but looks great

[Ginola]

I do like titanium!!

[KevP84]

very interesting. looks really good

[seventune]

Cheers chaps.

Finally got pipe one done. Started work on the bigger rims too.

One down, one to go...






Wheels. 18x10 ET12 with a future 25mm added on for good measure.

New colour; but first a big mess!



Then it started raining so had to bring them in for a bit



Woop done.

[KevP84]

wow!! like the colour of them wheels

[seventune]

Cheers fella,

Just a quick few of the other pipe now all done. I have to say now the ti is blue like the fittings the red wastegate is really bugging me....







So started getting the shape together for the rear arches. A teaser of things to come....

[seventune]

Right. Scoob is leaving the workshop tomorrow to go home as I'm taking some time off work for a bit and it will give me something to keep me occupied

I have started really chomping away at the inner arches now to suite new wide arches. I've also a ordered a couple of bits off ABW that will need to be modded a bit to suite the wide arch width. Becuase everyone needs wide body impreza in their lives.

Also ordered a few guages that turned up this morning.

Oil pressure
Boost pressure
Air/fuel
Oil temp
Water temp
Exhaust temp

Also a dash pod to suite. Once these bits are in and body is done I'm going to do the loom and get it mapped.

[seventune]

Well. Can went on a transporter yesterday and found its way home so I could get cracking with the body. I hadn't finished the 2nd two wheel yet hence the yellow ones

On the transporter and off she goes:



Hour later and the old girl is home; lots to do:



That was yesterday. Being off today I started setting about the arch work. There is a bit of shaping to do and I'm. Waiting on some bits from ABW.

First off. 18x10s all round.



The some arches

[Red Baron]

Like the fact you've split the arch where it joins the front bumper, will you do the same on the rear ones?

[seventune]

Yes I will. Not sure how I will shape the bottom of the arch Yet so just left it alone for now.

[seventune]

[alfa male]

Smooth and phat.......... I like!