South East Scoobies  

Go Back   South East Scoobies > The Garage > General Mechanics
Reload this Page oil pressure
FAQ Calendar

Reply
 
Thread Tools
  #1  
Old 14-04-2012, 07:35 PM
andy-m's Avatar
andy-m andy-m is offline
Silver Member
  
Join Date: Apr 2010
Location: SE London
Posts: 1,148
Default oil pressure
anyone with a classic running 10W-50 and a oil pressure gauge, what oil pressures are you getting?

i've just done my oil change and fitted the oil pressure sensor so my newly fitted oil gauge works.
once warmed up I seem to be getting 2.8bar on idle, and off the gauge once I go over 2000rpm (gauge only goes up to 7 bar)
Reply With Quote
  #2  
Old 14-04-2012, 08:16 PM
kartingsteve's Avatar
kartingsteve kartingsteve is offline
Silver Member
  
Join Date: Sep 2008
Location: Surrey
Posts: 551
Default
I have a bugeye and that seems about right.
Reply With Quote
  #3  
Old 14-04-2012, 08:31 PM
C. J.'s Avatar
C. J. C. J. is offline
Platinum Member
  
Join Date: Sep 2008
Location: Horsham
Posts: 5,081
Default
Mines 3bar on tick over 9bar on throttle
__________________
Eat, Sleep, Race , Repeat
Reply With Quote
  #4  
Old 14-04-2012, 08:40 PM
andy-m's Avatar
andy-m andy-m is offline
Silver Member
  
Join Date: Apr 2010
Location: SE London
Posts: 1,148
Default
cheers, wasnt sure if i was getting correct readings or if the gauge/sender was faulty but given the feedback, I think it seems about right
Reply With Quote
  #5  
Old 14-04-2012, 11:41 PM
kartingsteve's Avatar
kartingsteve kartingsteve is offline
Silver Member
  
Join Date: Sep 2008
Location: Surrey
Posts: 551
Default
Quote:
Originally Posted by C. J. View Post
Mines 3bar on tick over 9bar on throttle
you must have a better oil pump .
Reply With Quote
  #6  
Old 15-04-2012, 12:10 AM
Jolly Green Monster Jolly Green Monster is offline
Rest in peace Simon.
  
Join Date: Sep 2008
Location: Maidstone
Posts: 1,104
Default
it wont just be oil pump, but yes that effects it obviously but oil pressure will be influenced by many aspects.. bearing condition and clearances, avcs heads and pump size.. there are 10mm, 11mm and 12mm pumps.

My 6cylinder has 2bar idle and 4bar on throttle (fairly normal for an EG33).. its got more bearings to run the oil round so more have leaked out and lost the pressure

Simon
__________________
Jolly Green Monster Limited
Full time mapper and Ecu Expert - EcuTek 99 to 2010, ESL 93 to 96, Apexi, Motec, Autronic, Link, GEMs, Simtek, Solaris/Syvecs remaps

www.JollyGreenMonster.co.uk

Please follow of Facebook http://www.facebook.com/pages/Jolly-...26125404073166
Reply With Quote
Reply

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 



All times are GMT +1. The time now is 08:25 PM.

Contact Us - SouthEastScoobies - Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.

Opinions expressed are not necessarily the opinions of SouthEastScoobies or any individuals directly or indirectly involved in this website. No responsibility is taken or assumed for any comments or statements made on this or any associated website. Visitors who use this website and rely on, or act on any information do so at their own judgement, discretion and or risk. SouthEastScoobies or its content providers shall not be liable for any loss or damage arising from or otherwise in connection with your use of SouthEastScoobies forums. It is not possible for the Administrators of these forums, or the Moderators participating, to fully and effectively monitor Messages that are submitted for infringement of third party rights. If you believe that any information within the forums infringes your legal rights, or gives cause for concern you should notify an Administrator or a Moderator immediately giving such information to enable the recipient to amend, delete or remove in its entirety the message, at their earliest convenience.